Sunrise Fire Private Limited

Intelligent (addressable) detectors with point ID capability that enable each detector address to be set with rotary address switches to provide exact detector locations. Our thermal detectors use an innovative thermistor sensing circuit to produce 135°F fixed, rate-of-rise and 190°F high-temperature detection for cost-effective, intelligent property protection.

Features & Benefits:

• Sleek, low-profile design
• Thermal smoke detection
• Analog communications
• Low standby current
• Rotary address switches
• Dual LEDs for 360° visibility

• FST-951-IV Series Thermal Heat Detector
• FST-951H Series Thermal Heat Detector
• FST-951H-IV Series Thermal Heat Detector
• FST-951R Series Thermal Heat Detector
• FST-951R-IV Series Thermal Heat Detector

Intelligent (addressable) detectors with point ID capability that enable each detector address to be set with rotary address switches to provide exact detector locations. Our thermal detectors use an innovative thermistor sensing circuit to produce 135°F fixed, rate-of-rise and 190°F high-temperature detection for cost-effective, intelligent property protection. The FST-851 is a Fixed Temperature Thermal Detector for use with ONYX Series panels.

The FST-851R is a Rate-of-Rise Thermal Detector for use with ONYX Series panels. The FST-851H is a High Temperature Thermal Detector for use with ONYX Series panels.

Features & Benefits:

• Thermal smoke detection
• Analog communications
• Low standby current
• Rotary address switches
• Dual LEDs for 360° visibility

• FST-851 Fixed Temperature Thermal Detector
  • Operating Temperature:  –4°F to 100°F (–20°C to 38°C)
• FST-851R Rate-of-Rise Thermal Detector
  • Operating Temperature: –4°F to 100°F (–20°C to 38°C)
• FST-851H High Temperature Thermal Detector
  • Operating Temperature: –4°F to 150°F (–20°C to 66°C)
• Rotary address switches
• Dual LEDs for 360° visibility

FSP-851 Photoelectric Smoke Detector: Our photoelectric detector’s unique optical sensing chamber is engineered to sense smoke produced by a wide range of combustion sources. Intelligent (addressable) detectors include point ID capability that enable each detector address to be set with rotary address switches to provide exact detector locations. The sensitivity can be programmed using the control panel software to suit the environment. In addition, detector sensitivity is continually monitored and reported to the panel. The FSP-851 is a Photoelectric detector for use with ONYX Series panels. The FSP-851T is a Photoelectric detector with thermal detection for use with ONYX Series panels. The FSP-851R is a Photoelectric detector suitable for use with DNR(W) duct smoke detectors and ONYX Series panels.

Features and Benefits:

Photoelectric smoke detection

Analog communications

Low standby current

Rotary address switches

Dual LEDs for 360° visibility

Specifications:

FSP-851 - Photoelectric smoke detection Operating temperature: 32°F to 120°F (0°C to 49°C)

FSP-851T - Photoelectric smoke detection with thermal detection

Operating temperature:  32°F to 100°F (0°C to 38°C)

FSP-851R - Photoelectric detection suitable for use with DNR(W) duct smoke detectors

Operating temperature: 32°F to 120°F (0°C to 49°C)

Rotary address switches for point identification and quick installation

Dual LEDs for 360° visibility

Available Models:

• FSP-951T Photoelectric Smoke Detector
• FSP-951T-IV Photoelectric Smoke Detector
• FSP-951R Photoelectric Smoke Detector
• FSP-951R-IV Photoelectric Smoke Detector

InnovairFlex™ duct smoke detectors simplify the duct detection installation process saving you time and money while still providing the flexibility you need in the field. The DNR is an Intelligent non-relay photoelectric duct smoke detector for use with ONYX Series panels. The DNRW is a Watertight intelligent non-relay for use with ONYX Series panels.The FSL-751DNR is an Intelligent, high sensitivity duct smoke detector for use with ONYX Series panels.

Features & Benefits:

• Air velocity rating from 100 ft/min to 4,000 ft/min
• Adjusts to square and rectangular mounting configurations
• Patented tool-free, plug-in sampling tubes

• DNRW Duct Smoke Detector
• FSL-751DNR Duct Smoke Detector

For use in areas where smoke detection is impractical due to high level of dust, dirt, steam and high humidity. Selectable parameter sets for rate of rise and fixed temperature.
The base must be ordered separately.
Scope of delivery
Detector and dust cap

The IntelliQuad PLUS FCO-951 Series Advanced Multi-Criteria Fire/CO Detector incorporates photoelectric, thermal, infra-red and carbon monoxide detection principles, providing both fire and CO detection. Sophisticated algorithms maximize the advantages of all four sensor types creating our best detection strategy; offering heightened immunity to nuisance particulate and enhanced sensitivity to real fire.

Features & Benefits:

• Sleek, low profile design with optional color features
• 10-year CO cell with end-of-life warning
• Highest nuisance alarm immunity, Unique ability to detect all four major elements of a fire

• FCO-951-IV Series Advanced Multi-Criteria Fire Detector 

FS-OSI-RI(A) Addressable Reflective Beam Smoke Detector is designed for spacious rooms, open areas, and high ceilings. With only one device to install and align, these single-ended optical beam solutions saves you time and money on large area applications.

Features & Benefits:

• LED guided alignment
• 16 to 328 foot protection range
• Built-in test feature
• Paintable cover

• FS-OSI-RI Single-ended beam smoke detector
  • 16 to 328 foot protection range
  • Single-ended, reflected type design
  • Paintable cover

FPTI-951 Series Multi Sensor Detector: The PTIR detector is an intelligent, multi-criteria detector incorporating photoelectric, thermal and infrared detection principles to sense a wider range of fires with greater accuracy.

Features & Benefits:

• Multi-Criteria Detection
• New modern profile with color options available
• Analog communications
• Duel LEDs for 360 degree visibility

• FPTI-951 Multi-Criteria Photo/Temp/Infrared Detector
• Photoelectric, thermal and infrared smoke detector (White)
• Operating Temperature 32F - 100F (0C - 38C)
• FPTI-951-IV (same but Ivory)

• FPTI-951-IV Series Multi Sensor Detector

• Extended monitoring area

• Transmitter, receiver, and evaluating unit integrated into a compact housing

• Electronic help for detector alignment and automatic detector calibration procedure

• Automatic compensation for contamination

• LED display in control unit for various operating states

• Adjustable alarm thresholds

The new Simplex Addressable Beam Detector combines the power and flexibility of IDNet technology with the proven performance of the FireRay 5000 optical beam smoke detector. Beam Detectors are used to provide “open area” smoke detection in situations where it is either impractical or not cost effective to use traditional point-type detectors or aspirating smoke detection. Some common applications are: Warehouses; Atriums; Convention Centers; Shopping Malls; Sports Arenas.

The addressable beam detector provides enhanced command, control, configuration and status / event reporting between the detector and the fire alarm control panel. Configuration, installation, diagnostics, service and maintenance of this new addressable detector is also simpler and faster than a conventional detector and separate IDNet module, saving time and money for contractors, installers and building owners.

The addressable beam detector is compatible with Simplex 4100ES and 4010ES fire alarm control panels. Key features:

• Up to 2 Detector Heads reporting to One Ground Level Controller
• Range of 26 ft, 3 inches to 330 ft (8 m to 100 m)
• Built in Laser assisted prism mounting
• Built-In electronic UL/ULC obscuration acceptance Fire Test
• Contamination compensation
• Fire alarm control panel operations include: Sensitivity selection, Almost Dirty threshold, Initiate obscuration test
• Fire alarm control panel information received includes: Smoke status, controller-to-detector communications status, trouble status, Analog values for signal strength and compensation level

The system is designed to be mounted so the beam will project between 19” (0.5m) and 24” (0.6m) below and parallel to the ceiling. Lateral detection may be up to 30ft. (9.144m) on either side of the beam, providing a maximum total coverage area of up to 19,800 square feet (60ft. x 330ft. or 18.29m x 100m).

• Use in ventilation systems with air velocities from 1 m/s to 20 m/s

• For the activation of fans, door controls or external display devices an optional Relay Board can be installed

• A clear section on the frosted cover allows observing the alarm LED of the integrated FAD-425-O-R Detector

• Control to prevent unwanted removal of the cover

• Easy installation of the FAD-425-O-R Detector

• Maintains LSN loop functions in the event of wire interruption or short-circuit thanks to two integrated isolators

The NOTIFIER FPC-951 is an intelligent, multi-criteria detector incorporating photoelectric and carbon monoxide (CO) detection principles. It offers a cost-effective solution that meets both the UL 268 7th edition standard for smoke detection and UL 2075 standard for system-connected life safety carbon monoxide detection.

Features & Benefits:

• Combination smoke and CO detector
• Sleek, low profile design with optional color features
• 10-year CO cell with end-of-life warning

Features & Benefits:

• Life safety Carbon Monoxide detection
• Automatic drift compensation of the CO cell
• CO cell end-of-life warning and fault

Our photoelectric detector’s unique optical sensing chamber is engineered to sense smoke produced by a wide range of combustion sources. Intelligent (addressable) detectors include point ID capability that enable each detector address to be set with rotary address switches to provide exact detector locations. The sensitivity can be programmed using the control panel software to suit the environment. In addition, detector sensitivity is continually monitored and reported to the panel.

Features & Benefits:

• Sleek, low-profile design
• Available in both Bright White (for new installations) and Ivory (for legacy installations)
• Photoelectric smoke detection
• Analog communications
• Low standby current
• Rotary address switches
• Dual LEDs for 360° visibility

Our most advanced intelligent spot detectors, multi-criteria/multi-sensor devices use multiple sensors to detect various conditions in an environment sensing a wider range of fires with greater accuracy. The FSC-851 is a Advanced Multi-Criteria Fire Detector for use with ONYX Series panels. 

Available Models

• The FAPT-851 is a Multi-Criteria Detector for use with ONYX Series panels.

Features & Benefits:

• Multi-Criteria/Multi-Sensor smoke detection
• Unique ability to detect major elements of a fire
• Highest nuisance alarm immunity
• Advanced algorithms interpret and respond to multiple inputs

Reflected Beam Smoke Detector is designed for spacious rooms, open areas, and high ceilings. With only one device to install and align, these single-ended optical beam solutions saves you time and money on large area applications.
Available Models
The FSB-200S is a Single-ended beam smoke detector with integral sensitivity test for use with ONYX Series panels.
Features & Benefits:
16 to 328 foot protection range
Single-ended, reflected type design
Paintable cover

The NOTIFIER FSCO-951 is an intelligent carbon monoxide (CO) detector. It offers an addressable solution that meets the UL 2075 standard for system-connected life safety carbon monoxide detection.

Features & Benefits:

• Addressable CO detector
• Sleek, low profile design with optional color features
• 10-year CO cell with end-of-life warning

Duct Smoke Detector: Innovair Flex™ Duct Smoke Detector simplify the duct detection installation process saving you time and money while still providing the flexibility you need in the field.

Features and Benefits:

• Air velocity rating from 100 ft/min to 4,000 ft/min
• Adjusts to square and rectangular mounting configurations
• Patented tool-free, plug-in sampling tubes

• DNR Intelligent non-relay photoelectric duct smoke detector
  • Operating Temperature: –4°F to 158°F (–20°C to 70°C) 
  • Air Velocity:  Air velocity rating from 100 to 4,000 FPM
  • Detector head sold separately.
• DNRW Watertight intelligent non-relay photoelectric duct smoke detector
  • Operating Temperature: –4°F to 158°F (–20°C to 70°C) 
  • Air Velocity:  Air velocity rating from 100 to 4,000 FPM
  • Detector head sold separately.
  • NEMA Type 4 type 4 enclosure
• FSL-751DNR Intelligent, high sensitivity duct smoke detector
  • Operating Temperature: 32°F to 100°F (0°C to 38°C)
  • Air Velocity: Air velocity rating from 300 to 4,000 FPM
• Adjusts to square and rectangular mounting configurations
• Patented tool-free, plug-in sampling tubes 

• The FIRERAY 5000 System is an auto-aligning, self-correcting infrared beam smoke detector. Up to 2 detector heads can report to a single ground level controller. Once the detector head is installed, using the easy-fit mounting system an integral laser can be activated. This allows the reflective prism to be located quickly and with confidence.
• The Auto-Align function ensures proper alignment and maximum signal during the beam installation. The AutoOptimise feature automatically steers and maintains the beam in the optimum position for reliable performance. The signal generated in the transmitter element and reflected by the prism back to the receiver element is analyzed for the presence of smoke. The internal microprocessor determines an alarm condition when a predetermined level obscuration is reached.
• The system is designed to be mounted so the beam will project between 19” (0.5m) and 24” (0.6m) below and parallel to the ceiling. Lateral detection may be up to 30ft. (9.144m) on either side of the beam, providing a maximum total coverage area of up to 19,800 square feet (60ft. x 330ft. or 18.29m x 100m). 
• The FIRERAY 3000 End to End infrared Beam Smoke Detector has been designed using the latest optical technology, incorporating modern industrial, electronic and software techniques. This detector offers cost effective protection of large, open area spaces with high ceilings. It is also very suited to applications where access to ceiling mounted smoke detectors presents practical difficulties.
  
  The FIRERAY 3000 is ideal for applications where line of sight for the IR (infra-red) detection path is narrow and where the building structure uses reflective surfaces. It has also been designed to be aesthetically pleasing and thus can equally suit modern architectural buildings as well as historical sites, particularly where ornate ceilings exist.
• Open-area Smoke Imaging Detection (OSID) by Xtralis is a new innovation in projected beam smoke detection technology. By using advanced dual wavelength projected beams and optical imaging technology, OSID provides a low-cost, reliable and easy to install solution that overcomes typical beam detection issues such as false alarm incidents and alignment difficulties.
• The OSID system measures the level of smoke entering beams of light projected over an area of protection. A single OSID Imager can detect up to seven Emitters to provide a wide coverage area.