Single Loop Panel

Product Details:

• 8 sensor groups with up to 30 sensors in each sensor group (conventional panel supports up to 240 conventional devices in total)
• Large LCD display with 8 rows x 40 characters
• Integrated sensor group single display
• Optimized commissioning, maintenance and operation
• Simple configuration and programming on the keypad
• Four relays, freely programmable, non-monitored, potential free, max. 30 V DC / 2 A or 60 V DC / 1 A
• 2 outputs for connecting acoustic or optical sounders according to EN 54-13 (29 V DC/ max. 500 mA)
• 1 interface to a transmission unit for fire alarm routing equipment (FARE) (12 V DC / max. 200 mA)
• 1 interface to a transmission unit for fault warnings (12 V DC / max. 200 mA)
• 1 standard interface extinguisher for fire control system type C according to DIN EN 54-2
• RS485 for connecting to fire brigade operating panel and fire brigade display panel
• 1 output UBext 29 V / 0.5A, for power supply of external bus users
• 72 h emergency current bridge
• “Delay of relaying” function (PM operating mode according to DIN VDE 0833-2 for preventing false alarms, delay / verify)
• “2-detection dependency” function (TM operating mode according to DIN VDE 0833-2 for preventing false alarms), alternatively programmable as intermediate alarm storage or 2-zone dependency between the detector zones
• Operating panel with alphanumerical display
• Large LCD display with 8 rows x 40 characters
• Alarm counter for up to 10,000 trips
• Event memory for up to 10,000 events

Product Details:

• Single loop panel (system supports up to 127 digital loop addresses in total)
• Integrated esserbus-PLus (loop powered)
• Short circuit and open circuit tolerant loop operation with stub cable exits
• Operation of bus-supplied, synchronously controlled alarm generators (optical/acoustic/voice) in different alarm areas via esserbus-PLus powered loop technology
• Length of the loop circuit (esserbus) up to 3.5 km
• Up to 127 esserbus devices (fire detectors or manual call points)/group
• Up to 32 esserbus transponders
• Up to 30 IQ8Quad detectors with integrated sounders
• Up to 20 IQ8Alarm / IQ8Alarm Plus sounder
• Operation of ATEX approved detectors (intrinsically safe) for potentially explosive areas
• Optimized commissioning, maintenance and operation
• Easy configuration and programming of the FACP functions via display
• 4 relays, programmable, not monitored, potential-free, max. 30 V DC/2 A or 60 V DC/1 A
• 2 outputs for connection to acoustic and optical sounders according to EN 54-13 (each 24 V DC/max. 500 mA)
• 1 interface to a transmission unit (TU) for Fire alarm routing equipment (FARE) (12 V DC/max. 200 mA)
• 1 interface to a transmission unit (TU) for fault reports (12 V DC/max. 200 mA)
• 1 standard interface solution for fire control type C acc. DIN EN 54-2
• RS485 for connection of fire brigade control panel and fire brigade graphic annunciator
• 1 output UBext 24 V/0.5 A, for the voltage supply of external devices
• 72 hour emergency bypass (depending on configuration)
• Integrated detector groups individual display
• Function "delay the transmission" (according to DIN VDE 0833-2, to avoid false alarms, delay/investigate)
• Function "two-message dependency" (according to DIN VDE 0833-2, to avoid false alarms), alternatively programmable as alarm caching, multi-group dependence or multi-detector dependency
• Operating panel with alphanumerical display
• Large LCD display with 8 rows x 40 characters
• Alarm counter for up to 10,000 trips
• Event memory for up to 10,000 events

• Rated voltage:  230 V AC 
• Rated frequency  50 Hz ... 60 Hz 
• Rated current  0,84 A 
• Output voltage  29 V DC 
• Quiescent current  approx. 100 mA 
• Battery capacity  max. 2 x 12 V/12 Ah 
• Ambient temperature  -5 to 45 Degree Celsuis 
• Storage temperature  -5 to 50 Degree Celsuis